Efficacy of microchips and 3D sensors for orthodontic force measurement: A systematic review of in vitro studies.

OBJECTIVE: To evaluate the efficacy of microchips and 3D microsensors in the measurement of orthodontic forces. METHODS: Through September 2023, comprehensive searches were conducted on PubMed/MEDLINE, SCOPUS and SCIELO without restrictions. RESULTS: After removing duplicate entries and applying the eligibility criteria, 23 studies were included for analysis. All the studies were conducted in vitro, and slightly more than half of them were centred on evaluating orthodontic forces exerted by aligners. Eight utilized microchips as measurement tools, while the remaining studies made use of 3D microsensors for their assessments. In the context of fixed appliances, key findings included a high level of agreement in 3-dimensional orthodontic force detection between simulation results and actual applied forces. Incorporating critical force-moment combinations during smart bracket calibration reduced measurement errors for most components. Translational tooth movement revealed a moment-to-force ratio, aligning with the bracket's centre of resistance. The primary findings in relation to aligners revealed several significant factors affecting the forces exerted by them. Notably, the foil thickness and staging were found to have a considerable impact on these forces, with optimal force transmission occurring at a layer height of 150 µm. Furthermore, the type of material used in 3D-printing aligners influenced the force levels, with attachments proving effective in generating extrusive forces. Deliberate adjustments in aligner thickness were observed to alter the forces and moments generated. CONCLUSIONS: Microchips and 3D sensors provide precise and quantitative measurements of orthodontic forces in in vitro studies, enabling accurate monitoring and control of tooth movement.

Functionality testing of an innovative biomechanically optimized and surface-modified orthodontic mini-screw-a comparative study.

PURPOSE: The failure rate of orthodontic mini-screws depends strongly on primary stability and, thus, on insertion torque. Further improvement regarding the failure rate might be achieved by modifying the surface coating. Therefore, the aim of the study was to investigate the stability of a newly designed and surface-modified orthodontic mini-screw in beagle dogs. METHODS: Newly designed mini-screws coated either with DOTIZE® or DOTIZE®-copper (DOT GmbH, Rostock, Germany; each: n = 24) were inserted in the mandibles of eight beagle dogs for a duration of 8 months. Insertion and removal torque were measured. These data were compared to values generated by using the artificial bone material Sawbones® (Sawbones Europe AB, Malmö, Sweden). Experiments with and without torque limitation (each: n = 5) were run. The bone-to-implant contact rate and the amount of bone between the threads were examined. Statistical significance was set at P < 0.05. RESULTS: The success rates of the in vivo study reached high levels with 95.3% for the DOTIZE-coated and 90.5% for the DOTIZE-copper-coated screws, whereas the insertion and removal torque did not differ between the coatings. During insertion, a torque limitation of 20 Ncm was necessary to ensure that the recommended limit was not exceeded. The insertion in Sawbones without torque limitation revealed a significantly higher torque compared to torque-limited insertion (18.2 ± 1.3 Ncm, 23.6 ± 1.3 Ncm). Bending occurred (n = 5) in the thread-free part of the mini-screw. CONCLUSIONS: Surface coating might be able to improve the performance of orthodontic mini-screws. The study showed high success rates and stable mini-screws until the end of observation. Further investigations are necessary.

Simplifying two-vector mechanics calculations for challenging tooth movements.

The purpose of this article was to describe a simple graphical driven method for determining the necessary two-vector mechanics (TVM) as an alternative solution to the ideal or single force. In orthodontics, some tooth movements are difficult to achieve, mainly because of the impossibility of getting the point of application for the necessary force system. Given two points in biomechanically accessible areas, adding together two vectors applied to those points will result in an equivalent force system. The method was developed based on previous research, 3,880 hypothetical cases were analyzed to determine the trends between the resulting forces and their relative locations. A graphical driven TVM method (GTVM) for establishing the necessary TVM is presented in a manner that combine different procedures from the traditional method that simplify the analysis and may allow the user to perform more complex orthodontic cases making easier to compare systems of force equivalents.

Orthodontic correction of anterior open bite using skeletal anchorage: systematic review and meta-analysis.

The purpose of this study was to investigate the scientific evidence on the short- and long-term effects of orthodontic correction of anterior open bite (AOB) using skeletal anchorage (SA). Clinical studies on the use of SA for AOB in patients with permanent dentition, or at least 12 years of age, were searched. Short- and long-term (≥2 years) outcomes were collected. Mean differences were calculated from pooled data. Twenty-four eligible articles with a total of 362 subjects were selected for inclusion in the meta-analysis. There was a significant increase in overbite (3.88 mm, P < 0.001) and maxillary molar intrusion (-2.15 mm, P < 0.001). The mandible showed counterclockwise rotation with anterosuperior chin movement (all P < 0.001). Long term, the decrease in overbite was 19.9% and decrease in molar intrusion was 22.9%. The decrease in the mandibular projection was 14.6% for ANB (A-point-nasion-B-point angle) and 46.2% for mandibular anteroposterior position. The overall risk of bias in the included studies was rated as moderate to high, and publication bias existed for several key variables. SA for maxillary molar intrusion effectively improved dental and skeletal outcomes, but there was a long-term decrease in overbite and maxillary molar position. The variable data quality, heterogeneity, and publication bias in investigated outcomes are limitations in interpreting the findings.

Contribution of Digital Technology to the Surgical Technique of Miniscrew Insertion: a Literature Review

Orthodontic miniscrews are used to achieve absolute anchorage. Their insertion technique is simple but must be precise to avoid intra- and postoperative complications. This study aimed to review the literature on the role of digital technology in the precise placement of miniscrews and to describe the different stages of the insertion guide manufacturing chain. The databases used were PubMed, Science Direct, and Google Scholar, including the following English descriptors: "Orthodontic Anchorage Procedures," "Cone Beam Computed Tomography." Digital technology improves the accuracy of miniscrew placement by using 3D imaging to assess the quantity and quality of bone and the proximity of anatomical structures in the area to be implanted. By combining 3D imaging with the new techniques of 3D printing and virtual planning, the orthodontist can obtain a personalized placement guide for the patient using computer-aided design and manufacturing techniques. A digitally-assisted miniscrew insertion system is a promising technique for precise and safe miniscrew insertion but cannot be used routinely. Therefore, large-scale studies are needed to map miniscrew insertion in different areas, considering ethnicity, gender, and different anatomical characteristics.

Various surgical methods of impacted maxillary canine exposure: A case series.

Impacted tooth is often a common problem in dentistry. Maxillary canines are seen impacted most commonly in patients undergoing orthodontic treatment without reaching the line of occlusion. These impactions are commonly due to physical obstructions and the difference in the direction of movement of the tooth. Canines are the cornerstones for esthetic smile and functional occlusion. Hence, surgical exposure of these impacted canines, guiding them toward the line of occlusion, plays a very important role in the maintenance of the health of periodontium. A series of cases are discussed on various techniques that can be used in guiding the direction or altering the direction of impacted canines to bring them into a proper occlusion without disturbing the health of periodontium.

Finite element analysis of two skeletally anchored maxillary molar distalisation methods.

OBJECTIVE: To compare two methods of maxillary molar distalisation with skeletal anchorage using finite element analysis (FEA). METHODS: Two digitised models were created: the miniscrew-anchored distaliser, which consisted of a distalisation method anchored in a buccal miniscrew between the first molar and second premolar (Model 1), and the miniscrew-anchored palatal appliance, which consisted of a distalisation method anchored in a miniscrew on the anterior region of the palate (Model 2). FEA was used to simulate both methods, assessing teeth displacements and stress concentration. RESULTS: The miniscrew-anchored distaliser showed greater buccal than distal displacement of the first molar, while the opposite was observed in the miniscrew-anchored palatal appliance. The second molar responded similarly in the transverse and anteroposterior perspectives with both appliances. Greater displacements were observed at crown level than in apical regions. Greater stress concentration was observed at the buccal and cervical regions of the crown in the miniscrew-anchored distaliser and the palatal and cervical regions in the palatal appliance. The stress progressively spread in the buccal side of the alveolar bone for the miniscrew-anchored distaliser and in the palatal root and alveolar bone for the palatal appliance. CONCLUSION: FEA assumes that both appliances would promote maxillary molar distalisation. A skeletally anchored palatal distalisation force seems to provide a greater molar bodily movement with less undesirable effects. Greater stress is expected at the crown and cervical regions during distalisation, and the stress concentration in the roots and alveolar bone depends directly on the region the force was applied.

Tomographic evaluation of mandibular buccal shelf in patients with different vertical growth pattern / Evaluación de la placa ósea mandibular en pacientes con diferente patrón de crecimiento vertical

The purpose of this research was the tomographic evaluation of the Mandibular Buccal Shelf (MBS) in orthodontic patients with different vertical growth pattern. An observational, descriptive, cross-sectional and retrospective study was conducted. Tomographic images of patients aged 14 to 40 years were observed and a database was formed with those that met the inclusion criteria. The sample size was 10 for each group according to vertical growth pattern (hypodivergent, normodivergent and hyperdivergent). Then four zones of frequent insertion of extralveolar mini-screws were selected in the MBS, taking as a reference the mesial and distal roots of the first and second mandibular molar. When comparing the characteristics of MBS between vertical growth patterns, between sexes and hemiarchs, no statistically significant differences were found. However, when the characteristics of MBS were compared according to the reference root, it was found that there were statistically significant differences. The vestibular area to the distal root of the second mandibular molar presented the highest values in terms of angulation, height and thickness. There are no significant differences in the bone characteristics of MBS according to vertical growth patterns, sexes or hemiarchs. Angulation, height and thickness progressively increase from the vestibular bone of the mesial root of the first mandibular molar to the distal root of the second molar.

El propósito de esta investigación fue la evaluación tomográfica de la placa ósea mandibular (POM) en pacientes de ortodoncia con diferente patrón de crecimiento vertical. Se realizó un estudio de tipo observacional, descriptivo, transversal y retrospectivo. Se observó imágenes tomográficas de pacientes de 14 a 40 años de edad y se formó una base de datos con las que cumplían los criterios de selección. El tamaño de muestra fue de 10 para cada grupo según patrón de crecimiento vertical (hipodivergentes, normodivergentes e hiperdivergentes). Luego se seleccionaron cuatro zonas de inserción frecuente de minitornillos extralveolares en la POM, tomando como referencia las raíces mesial y distal del primer y segundo molar mandibular. Al realizar la comparación de las características de la POM entre patrones de crecimiento vertical, entre sexos y hemiarcadas no se encontraron diferencias estadísticamente significativas. Sin embargo, cuando se comparó las características de la POM según la raíz de referencia se encontró que había diferencias estadísticamente significativas. La zona vestibular a la raíz distal de la segunda molar mandibular presento los mayores valores en cuanto angulación, altura y grosor. No existen diferencias significativas en las características óseas de la POM según patrones de crecimiento vertical, sexos o hemiarcadas. La angulación, la altura y el grosor aumenta progresivamente desde el hueso vestibular de la raíz mesial del primer molar mandibular hacia la raíz distal del segundo molar.

Evaluation of stress distribution values at the temporomandibular joint and distalization of teeth during en-masse retraction of the mandibular dentition using buccal shelf bone screws: A FEM study.

INTRODUCTION: Present Finite-element-method (FEM) study evaluates the stress distribution values at the Temporomandibular-Joint (TMJ) during en-masse retraction of the mandibular dentition using buccal shelf bone screws with varying magnitudes of forces. MATERIAL AND METHODS: Nine replicas of a pre-existing three-dimensional finite element model of the craniofacial skeleton and articular disc from Cone-Beam-Computed-Tomography (CBCT) data and Magnetic-Resonance-Imaging (MRI) data of a patient were used. Buccal shelf (BS) bone screws were inserted buccal to the mandibular second molar region. Forces of magnitudes 250 gm, 350 gm and 450 gm were applied through NiTi coil springs along with stainless-steel archwires of sizes 0.016 × 0.022-inch, 0.017 × 0.025-inch and 0.019 × 0.025-inch. RESULTS: On the articular disc, the maximum stress was observed at the inferior region and the inferior part of the anterior and posterior zone at all force levels. The stress on the articular disc and displacement of teeth increased with increase in force levels in all the 3 archwires. The maximum stress at the articular disc and displacement of teeth was observed for 450 gm force and the least for 250 gm force. No significant difference in the amount of displacement of teeth or the stresses produced at the articular disc was seen with increasing the size of the archwire. CONCLUSION: With the present FEM study, we can deduce that it is better to use forces of lower levels on patients with temporomandibular-disorders (TMD) so as to reduce the stresses produced at the TMJ to avoid worsening of the TMD condition.

Failure rates and factors associated with infrazygomatic crestal orthodontic implants - A prospective study.

Objective: Infrazygomatic crestal (IZC) implants have gained increased popularity over the past few years. Hardly any studies have been done to assess the rate and reasons for failure of IZCs. This prospective study was planned and designed with the primary objective of assessing the rate of failure of bone-screws (BS) placed in the infrazygomatic crest. In continuation, the secondary objective was to assess the factors that were associated with the failure. Materials and methods: The study was carried out by taking a detailed case history, (age, gender, vertical skeletal pattern, medical history), photographic records, radiographs, and clinical examination of a total of 32 randomly selected. patients of south indian origin who required infrazygomatic implants bilaterally as the choice of anchorage conservation to retract their incisors. All selected subjects were required to take a PA Cephalogram after the implant placement. The age of the patients ranged from 18 to 33 with an average age of 25 years. The patient log was maintained which included the treatment mechanics, status of oral hygiene, stability of implants, time of loading of the implant, presence of inflammation and time of failure of implant. The angulation of implant was measured on a digital PA cephalogram using Nemoceph software. These parameters were examined to evaluate independent and dependent variables using the Chi-Square test and Fischer's exact test. Result: A failure rate 28.1% for IZC placed in the infrazygomatic crest region was observed. Patients with a high mandibular plane angle, poor oral hygiene, immediately loaded implant, peri-implantitis, and severe clinical mobility showed higher failure rates. Variables such as age, gender, sagittal skeletal pattern, length of the implant, type of movement, occluso-gingival position, method of force application, and angle of placement were not significantly associated with implant failure. Conclusion: Oral hygiene and peri-screw inflammation must be controlled to minimize the failure of bone screws placed in the infrazygomatic crest region. Loading of the implant should be done after a latent period of two weeks. A higher failure rate was observed in patients with vertical growth pattern.

Comparison of the Accuracy of Two Transfer Caps in Positional Transmission of Palatal Temporary Anchorage Devices: An In Vitro Study.

The aim of this study was to compare the positional information transfer accuracy of palatal temporary anchorage devices (TADs) of two different brands of transfer caps: PSM and Leone. Thirty plaster casts of maxillary dental arches were chosen for master models. A couple of Leone TADs were inserted in each master model. For each master model, two analysis models were created: using two transfer caps, Leone and PSM, the impressions were taken, the analogues were connected on the transfer caps, and the casts were poured. Using digital methods and equipment, such as a 3D scanner, a 3D analysis and a comparison of the accuracy of the two transfer caps in transferring the positional information of the TADs was then made. The data obtained were analyzed using the Mann-Whitney U-test at a significance level of α = 0.05. PSM transfer caps showed higher error frequency in almost all measurements. Only two measurements had a larger error in the analysis models made with Leone transfer caps. The Mann-Whitney U-test found a significant difference between the error levels of TADs found in the analysis models created with PSM transfer caps. Leone transfer caps showed greater reliability in TADs positional information transmission.

Treatment of Class II malocclusion with anterior open bite and posterior crossbite with the aid of mini-implants in a patient with Down syndrome: Clinical case report.

OBJECTIVE: We report the orthodontic treatment of a class II malocclusion with anterior open bite and posterior crossbite in a patient with Down syndrome (DS) treated with mini-implants. METHODS: Treatment began with rapid maxillary expansion with a Haas appliance, followed by dental alignment and leveling with a fixed appliance and the correction of class II dental relationships with the use of orthodontic mini-implants associated with a sliding jig. RESULTS: The results obtained at the end of the treatment were satisfactory, with improvements in occlusion, including bite closure; maxillary expansion; and the correction of dental relationships. CONCLUSION: When well-planned, orthodontic treatment in a patient with DS achieves satisfactory results from a skeletal, occlusal, and facial perspective.

Intrusion of overerupted periodontally compromised posterior teeth using orthodontic mini implants: A mechanobiological finite element study.

INTRODUCTION: The intrusion of posterior teeth had been considered challenging up to the development of orthodontic mini implants. In periodontally compromised teeth, the challenge is even greater, because of the root resorption risk due to periodontal ligament over-compression. Still, the precise strategy to determine the force reduction level remains uncertain. OBJECTIVE: The objective of the study was to determine, by a finite element analysis (FEA), the force reduction needed to avoid root resorption and maintain the efficiency of orthodontic mechanics of periodontally compromised teeth similar to the sound one. METHODS: An anatomical model was constructed representing a premolar inserted into a maxillary bone. Based on the initial model (R0), three bone height loss conditions were simulated (R2 = 2 mm, R4 = 4 mm, and R6 = 6 mm). Two intrusive movements were simulated: pure intrusion (bilateral mini implant) and uncontrolled-tipping intrusion (buccal mini implant). The hydrostatic stress at the periodontal ligament was used to evaluate the risk of root resorption due to over-compression. RESULTS: For bilateral mini implant intrusion, the force had to be decreased by 16%, 32% and 48% for R2, R4 and R6, respectively. For buccal mini implant intrusion, the required reductions were higher (20%, 36% and 56%). A linear relationship between the intrusive force reduction and the alveolar bone height loss was observed in both intrusion mechanics. CONCLUSIONS: According to the FE results, 8% or 9.3% of force reduction for each millimetre of bone height loss is suggested for intrusion with bilateral or buccal mini implant, respectively. The buccal mini implant anchorage must be associated with a supplemental strategy to avoid buccal crown tipping.

Influence of the palatal plane cant and skeletal patterns in the hard palate thickness?

INTRODUCTION: The aim of the present study was to evaluate the thickness of the hard palate at the different angles formed by the palatal plane and the Frankfort horizontal line using computed tomography in patients with different facial patterns for planning the installation of MARPE. MATERIALS AND METHODS: The measurements were analysed in the hard palate of 106 patients. Four regions were selected passing through the mesial face, tangent at the level of the cemento-enamel junction of the premolars and molars. The bone thickness was measured from the floor of the nasal cavity to the cortical bone of the hard palate, 02 measurements with a distance of 05 mm between them (2.5 mm on each side starting from the midsagittal line) and 2 more with a distance of 7 mm between measurements (3.5 mm on each side starting from the midsagittal line). The palatal plane cant was determined based on the palatal plane and the Frankfort horizontal plane. The sagittal skeletal pattern was determined based on the ANB angle and the vertical skeletal pattern based on the SN.Go.Gn angle. RESULTS: Palatal bone thickness was greater in males than in females. Regarding the sagittal skeletal pattern, patients with Class II were found to have a thinner hard palate than Class I and Class III patients. No difference in the vertical skeletal pattern was observed between groups. Regarding the palatal plane cant, bone thickness was greater in patients with clockwise rotation. CONCLUSIONS: Careful planning should be considered in the case of female patients; patients with greater angles of the palatal plane cant and Class II patients have a smaller bone thickness.

Rate of upper incisor retraction in Class II division 1 patients managed with palatal versus buccal miniscrew supported segmental orthodontics: Randomized parallel clinical trial.

OBJECTIVE: This study was conducted to compare maxillary incisor retraction rates using buccal orthodontics with segmented arch approach supported by a buccal or palatal mini-screw in non-growing Class II Division 1 patients during a 3-month period. PATIENTS AND METHODS: All patients between September 2018 and December 2021 with following criteria were included: non-growing class II division 1 protrusion, indication for premolar extraction, no or little crowding, normal overbite, no previous orthodontic treatment, no systematic disease, good oral hygiene, no periodontal problems or oral habits. Mini-implant was inserted buccally or palatally between upper second premolar and first molar bilaterally. Incisor retraction was manipulated by a 200-gram force through a nickel-titanium closed-coil spring extended from the mini-implant to the segmental design. Study casts were made before retraction and after every 4 weeks (T0: baseline, T1: 4 weeks, T2, 8 weeks, T3: 12 weeks). A repeated measures ANOVA was performed for total comparison of data (mm of retraction) on 3D casts. A pairwise t test with Bonferroni correction was used for comparison between two experimental periods for the same group. An independent samples t-test was also used for comparison between two groups for the same experimental period. RESULTS: Of 30 patients meeting the eligibility criteria, only 28 were included with mean age 16±2.5 years. Repeated measures ANOVA revealed significant differences in incisor retraction between the time intervals for both buccal and palatal groups (P=0.001). In addition, the paired-sample t test indicated a significant difference between each time interval for both the buccal and palatal groups (P=0.001), except between T3 and T2 for the palatal group (P=0.09). The independent sample t-test revealed significant differences between the buccal and palatal groups at T1 (Mean: 0.55 [0.355-0.748],=0.001) and T2 (Mean: 1.4 [0.91-1.88], P=0.001); whereas no significant difference was found at T3 (Mean: 1.15 [0.67-1.63], P=0.945). CONCLUSIONS: Anterior retraction using a segmental palatal model with mini-screws was effective regardless of the buccal or palatal situation of the minivis. Retraction of incisors with palatal miniscrews was significantly faster in the first two months.

Short-term assessment of pain and discomfort during rapid maxillary expansion with tooth-bone-borne and tooth-borne appliances: randomized clinical trial

ABSTRACT Objective: The aim of this randomized clinical trial was to evaluate and compare, during the first week of rapid maxillary expansion (RME), the impact caused by two types of appliances: Hyrax and Hybrid Hyrax. Methods: Forty-two patients who met the eligibility criteria (aged 11-14 years, with transverse maxillary deficiency, posterior crossbite, and presence of maxillary first premolars and first permanent molars) were selected and randomly divided into two groups: TBB GROUP (tooth-bone-borne expander), treated with Hybrid Hyrax (12 females and 9 males, mean age 13.3 ± 1.3 years), and TB GROUP (tooth-borne expander), treated with Hyrax (5 females and 16 males, mean age 13.3 ± 1.4 years). Pain and discomfort were assessed in two times: after the first day of activation (T1) and four days after, by means of the numerical rate scale and the instrument MFIQ (Mandibular Functional Impairment Questionnaire). Descriptive statistics and the Mann-Whitney test were used for comparison between groups and between sexes. A 5% significance level was adopted. Results: Both appliances had a negative impact, generating pain and discomfort, and reducing functional capacity. However, the scores obtained were of low intensity and no significant differences were observed between the groups. Considering sexes, there were statistically significant differences, with the female sex presenting higher scores for pain and functional limitation. Conclusions: Despite causing impact in pain and increase in the functional limitation, these changes were of low intensity, with no statistical difference between the groups. Females were more sensitive to the impact caused by the RME.

RESUMO Objetivo: O objetivo deste ensaio clínico randomizado foi avaliar e comparar, durante a primeira semana de expansão rápida da maxila (ERM), o impacto causado por dois tipos de aparelhos: Hyrax e Hyrax Híbrido. Métodos: Quarenta e dois pacientes que atendiam aos critérios de seleção (idade de 11 a 14 anos, com deficiência transversal da maxila, mordida cruzada posterior e presença de primeiros pré-molares e primeiros molares permanentes superiores) foram selecionados e divididos aleatoriamente em dois grupos: Grupo DOS (expansor dento-osseossuportado), tratado com Hyrax Híbrido (12 mulheres e 9 homens, idade média 13,3 ± 1,3 anos), e Grupo DS (expansor dentossuportado), tratado com Hyrax (5 mulheres e 16 homens, idade média de 13,3 ± 1,4 anos). A dor e o desconforto foram avaliados em dois momentos: após o primeiro dia de ativação (T1) e após quatro dias, por meio da escala de frequência numérica e do instrumento MFIQ (Questionário de Limitação Funcional Mandibular). A estatística descritiva e o teste de Mann-Whitney foram utilizados para comparação entre os grupos e entre os sexos. Adotou-se nível de significância de 5%. Resultados: Ambos os aparelhos tiveram impacto negativo, gerando dor e desconforto e reduzindo a capacidade funcional. No entanto, os escores obtidos foram de baixa intensidade e não foram observadas diferenças significativas entre os grupos. Considerando os sexos, houve diferenças estatisticamente significativas, com o sexo feminino apresentando maiores escores para dor e limitação funcional. Conclusões: Apesar de causar impacto na dor e aumento na limitação funcional, essas alterações foram de baixa intensidade, sem diferença estatística entre os grupos. As mulheres foram mais sensíveis ao impacto causado pela ERM.

Stress distribution in lower second molar mesialization using mini-implants: a pilot study using 3D finite element analysis / Distribuição de tensões na mesialização do segundo molar inferior usando mini-implantes: um estudo piloto usando análise de elementos finitos 3D

Objective: to analyze the stress distribution in a 3D model that simulates second molar mesialization using two different types of mini-implants. Material and Methods: a mandible bone model was obtained by recomposing a computed tomography performed by a software program. The cortical and trabecular bone, a lower second molar, periodontal ligament, orthodontic tube, resin cement and the mini-implants were designed and modeled using the Rhinoceros 4.0 software program. The characteristics of self-drilling orthodontic mini-implants were: one with 7 mm length, 1 mm transmucosal neck section and 1.6 mm diameter and another with 5 mm length and 1.5 mm diameter. A total of 235.161 and 224.505 elements were used for the mesh. These models were inserted into the bone block and then subjected to loads of 200 cN (centinewton). The results were calculated and analyzed by the Ansys 17.0 software program for qualitative verification through displacement and maximum principal stress maps. Results: it was possible to observe that the periodontal ligament presented low displacement and stress values. However, the physiological values presented are among those capable to provide orthodontic movement, with compression and tensile area visualization staggered between 0.1 and -0.1 MPa (megapascal). Conclusion: within the limitations of the study, the mini-implants tested showed similar results where the load on the tooth allowed dental displacement (molar mesialization), with a tendency to rotate it, theoretically allowing the second molar to take the location of the first molar. (AU)

Objetivo: analisar a distribuição de tensões em um modelo 3D que simula a mesialização do segundo molar usando dois tipos diferentes de mini-implantes. Material e Métodos: um modelo de osso mandibular foi obtido por recomposição de uma tomografia computadorizada realizada por um software. O osso cortical e trabecular, um segundo molar inferior, ligamento periodontal, tubo ortodôntico, cimento resinoso e os mini-implantes foram projetados e modelados no software Rhinoceros 4.0. As características dos mini-implantes ortodônticos auto perfurantes foram: um com 7 mm de comprimento, 1 mm de secção transmucosa e 1,6 mm de diâmetro e outro com 5 mm de comprimento e 1,5 mm de diâmetro. Para a malha, foram utilizados 235.161 e 224.505 elementos. Esses modelos foram inseridos no bloco ósseo e então submetidos a cargas de 200 cN (centinewton). Os resultados foram calculados e analisados pelo software Ansys 17.0 para verificação qualitativa por meio de mapas de deslocamento e tensões máximas principais. Resultados: foi possível observar que o ligamento periodontal apresentou baixos valores de deslocamento e tensões. Porém, os valores fisiológicos apresentados são capazes de proporcionar movimentação ortodôntica, com visualização da área de compressão e tração escalonada entre 0,1 e -0,1 MPa (megapascal). Conclusão: dentro das limitações do estudo, os mini-implantes testados apresentaram resultados semelhantes onde a carga sobre o dente permitiu o deslocamento dentário (mesialização do molar), com tendência a girá-lo, permitindo teoricamente que o segundo molar ocupe do lugar do primeiro molar (AU)

Mechanical Properties of Mini-Implants Used in Extra-Radicular Anchorage

ABSTRACT Objective: To evaluate the mechanical properties of mini-implants (MIs) manufactured from stainless steel and compare them with conventional titanium-aluminum-vanadium alloy MIs. Material and Methods: The following groups were formed: G1 (n=24), 8×1.5 mm steel MIs; G2 (n=24), 12×2.0 mm steel MIs; and G3 (n=24), 10×1.5 mm titanium MIs. The 72 MIs were inserted in the infra zygomatic crest region of the maxilla and retromolar trigone in the jaw of 10 pigs. Pull-out, insertion torque, fracture and percussion tests were performed in order to measure the tensile strength, primary stability and fracture strength of MIs. A digital torque gauge was used to measure insertion and fracture torque, a universal mechanical testing machine was used for pull-out testing and a periotest device was used to measure the micromovement of MIs. For morphological and MI component evaluation, scanning electron microscopy (SEM) was performed. D'Agostino & Pearson, Kruskal-Wallis, and Dunn post-hoc and normality tests were used. Results: G2 insertion and fracture torques were significantly higher than G1 and G3 insertion and fracture torques (p<0.05). The pull-out and percussion tests presented similar values among the groups. SEM revealed that the fracture point was predominantly on the fourth thread for steel MIs (G1 and G2) and on the seventh thread for titanium-aluminum-vanadium MIs (G3). Conclusion: The mechanical properties of stainless steel MIs are superior to those of titanium-aluminum-vanadium alloy MIs.

Proposta de tratamento ortopédico de paciente Classe III com hyrax modificado e máscara facial ­ relato de caso / Orthopedic treatment proposal of patient Class III with hyrax modified and facial mask ­ case report

Resumo Objetivo: Demonstrar a confecção de um hyrax híbrido apoiado em mini-implante, para o tratamento da classe III. Caso clínico: Paciente D. B. S, sexo masculino, 07 anos de idade, com mordida anterior de topo e mordida cruzada posterior unilateral direita, apinhamento leve nos incisivos inferiores, perda precoce decorrente de cárie dos elementos dentários 54 e 64 e atresia maxilar, contribuindo para a diminuição do perímetro do arco. Discussão: Em pacientes que possuem deficiência maxilar o tratamento deve englobar a estimulação e o direcionamento maxilar através de forças ortopédicas. A terapia com a Expansão Rápida da Maxila (ERM) em associação com a Máscara Facial (MF) é o tratamento mais habitual para a má oclusão classe III sendo utilizada para o tratamento da maxila retruída e também para que se acelere o crescimento maxilar. A utilização da ancoragem esquelética como forma de tratamento precoce da classe III resulta em efeitos ortopédicos fundamentalmente maiores se comparado com o tratamento convencional, desta forma, permite que não haja deslocamento dentário provocado pela força exercida durante a protração maxilar e evitando perda de espaço no perímetro do arco. Conclusão: a ancoragem esquelética vem ampliando as fronteiras dos tratamentos ortodônticos e ortopédicos, aumentando, com isso, a época de início da terapia sem efeitos dentários adversos, sendo a modificação de um hyrax convencional para um híbrido uma opção de melhor custo benefício e biológico. (AU)

Abstract Objective: To demonstrate the construction of a mini-implant-supported hybrid hyrax for the treatment of class III. Case report: Patient DB S, male, 07 years old, with upper anterior bite and right unilateral posterior crossbite, light crowding of the lower incisors, early loss due to caries of the teeth 54 and 64 and maxillary atresia, contributing to the decrease in the perimeter of the arch. Discussion: In patients who have maxillary deficiency, treatment should include maxillary stimulation and direction through orthopedic forces. Therapy with Rapid Maxillary Expansion (RME) in association with Facial Mask (MF) is the most common treatment for class III malocclusion and is used for the treatment of retruded maxilla and also to accelerate maxillary growth. The use of skeletal anchorage as a form of early class III treatment results in fundamentally greater orthopedic effects compared to conventional treatment, thus allowing for no tooth displacement caused by the force exerted during maxillary protraction and avoiding loss of space in the perimeter of the bow. Conclusion: skeletal anchorage has been expanding the frontiers of orthodontic and orthopedic treatments, thereby increasing the time to start therapy without adverse dental effects, with the modification of a conventional hyrax to a hybrid being a more cost-effective and biological option. (AU)

Effect of local administration of bisphosphonate on orthodontic anchorage - A systematic review of animal studies.

BACKGROUND: Pharmacological means of anchorage control can improve patient compliance. Bisphosphonates could be helpful in orthodontic anchorage control if their actions could be localized to limit (or control) unwanted tooth movement while not interfering with the desired tooth movement. OBJECTIVE: This systematic review aimed to examine and evaluate the quality of all animal studies that reported the effect of locally administered bisphosphonate on limiting orthodontic tooth movement. DATA SOURCES: An electronic search was conducted in the PubMed-Medline, Scopus, Google Scholar, and Cochrane databases till May 2022, using the keywords anchorage, anchorage loss, molar movement, posterior tooth movement, incisor movement, incisor retraction, anterior retraction, unwanted tooth movement, tooth displacement, tooth movement forward, bisphosphonate, local bisphosphonate administration, bisphosphonate injection, and bbisphosphonate vestibular induction. Only studies involving localized bisphosphonate administration for anchorage purposes were taken into account. DATA SELECTION: Animal studies that simulated orthodontic tooth movement after localized injection of bisphosphonate and evaluated the rate of tooth movement were included in the review. DATA EXTRACTION AND ANALYSIS: The quality of the studies was assessed by using ARRIVE guidelines (Animal Research: Reporting of In Vivo Experiments). Bias in the studies was analyzed by SYRCLE's tool (Systematic Review Centre for Laboratory Animal Experimentation) for risk of bias. RESULTS: The search strategy yielded 925 titles. After screening, 908 articles were discarded because they did not fulfill the inclusion/exclusion criteria based on the title and abstract. The remaining 16 articles were read entirely, of which nine were excluded as they involved systemic administration of bisphosphonates. Finally, after careful consideration, seven papers that met our inclusion criteria were included in the qualitative analysis. The majority of studies were assessed to have an uncertain risk of bias, with just one deemed low risk of bias. CONCLUSION: This systematic review found that bisphosphonates limit orthodontic tooth movement around the application site without affecting adjacent sites. More potent bisphosphonates in smaller doses or less potent bisphosphonates in higher frequencies have been proposed to improve outcomes. However, the data quality is insufficient to recommend a protocol for bisphosphonate administration for anchoring control. Long-term studies evaluating various types, frequencies, and dosages of bisphosphonates are required to clarify the effects on orthodontic tooth movement. REGISTRATION NUMBER FOR PROSPERO: CRD42021224033.